AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Lights out 2 compound bow9/7/2023 Most single-pin sights are sold today with multiple pre-printed sight tapes that vary based primarily on arrow speed. The indicator points to the sight tape, which has the yardage markings printed on it. There will be a movable indicator which adjusts between pre-set distances as the archer moves the scope housing. So these employ a sight tape, which is a yardage guide fixed to the sight body. Single-pin sights require the archer to adjust the scope housing up and down to shoot at different distances. Trouble is easy to avoid, however, if you shoot into that same large target that offers plenty of room for error. For windage, the 30, 40, 50, and 60 pins all should simply sit directly under the 20 in a straight, vertical line.Īdjustable sights with just one pin or other aiming reference are a little trickier to sight in, just because it’s difficult to gauge the initial adjustments. If your scope is properly leveled before you start, you should only have to move pins vertically after you zero your 20-yard pin. Repeat this process to set your 50 and 60-yard pins. Now shoot from 40 yards away using that third pin to aim. Keep shooting and moving that pin until your arrow consistently hits behind it.įor your 40-yard pin, look at the gap between your 20 and 30-yard pins and move your third-highest pin until the gap between it and the 30-yard pin looks similar to the gap from 20 to 30. This time - and for every pin afterwards - you’re only moving the pin, as opposed to the whole scope. Note where your arrow hits and move your second-highest pin into position. Once you feel confident your 20-yard pin is on, back up to 30 yards and shoot at the bull’s-eye again, using your 20 pin to aim. So when you set your 20-yard pin, put the pin high in the scope and then adjust the whole scope up and down and left and right until your arrow hits behind the pin at 20 yards. If you have five pins, you want that 20-yard pin near the top of the scope in order to have enough room in the scope for pins set at 10-yard increments out to 60 yards. Keep in mind you will need to have vertical room within your scope for however many pins your sight has. For example iIf the arrow hits high, move the pin up, and if the arrow hits to the right, move the pin to the right. The general rule you’ll follow when adjusting your sight is to always move the sight in the direction your arrows are hitting. Note where the arrow hits the target in relation to the bull’s-eye. Place a bull’s-eye in the center of the target and shoot at it from a distance of 10 yards, using your top pin as the aiming reference. And shoot into a large target - one with lots of room up and down and left and right. Let’s assume that arrangement.įor your first shot with a new sight, you’ll have no idea where that arrow is going to hit in relation to the bow sight pins, so start out shooting no farther than 10 yards. On a bowhunting sight, the most common way to set pins on a five-pin sight is to position them for aiming at 20, 30, 40, 50, and 60 yards, with the 20-yard pin being the highest aiming reference in the scope and the 60-yard pin being the lowest. With a multi-pin sight, you typically have three, five, or seven sight pins that you set as aiming references for different distances. How to Sight in a Multi-Pin Sight After your top pin is set, adjust each pin individually. Today’s compound sights essentially can be broken into two main categories - multi-pins and single pins. If you’re a do-it-yourselfer, head to YouTube and your sight’s directions will guide you on the process. If you take your bow to an archery shop the technician there can level your sight and tune your bow. If the sight sits on the bow at an angle, then every pin or sight reference you try to set after the first one will be off to the left or right. Leveling your sight is key to making sure that as you shoot at different distances, the left-right alignment of the sight stays true. If the bow - or archer - isn’t shooting straight, you can waste a lot of time trying to sight in. A tuned bow is one which has the rest and nocking point perfectly aligned so arrows leave the bow perfectly straight. The first step when it comes to how to sight in a compound bow is making sure the bow is tuned and your sight is leveled. How to Sight in a Compound Bow: Before You Begin
0 Comments
Read More
Leave a Reply. |